For a description of the older RAID layer, the one which is standard in 2.0 and 2.2 kernels, see the excellent HOWTO from Linas Vepstas ( linas@linas.org) available from the Linux Documentation Project at linuxdoc.org.
The home site for this HOWTO is http://ostenfeld.dk/~jakob/Software-RAID.HOWTO/, where updated versions appear first. The howto is written by Jakob Østergaard based on a large number of emails between the author and Ingo Molnar (mingo@chiara.csoma.elte.hu) -- one of the RAID developers --, the linux-raid mailing list (linux-raid@vger.rutgers.edu) and various other people.
The reason this HOWTO was written even though a Software-RAID HOWTO already exists is, that the old HOWTO describes the old-style Software RAID found in the standard 2.0 and 2.2 kernels. This HOWTO describes the use of the new-style RAID that has been developed more recently. The new-style RAID has a lot of features not present in old-style RAID.
If you want to use the new-style RAID with 2.0 or 2.2 kernels, you should get a patch for your kernel, either from ftp://ftp.[your-country-code].kernel.org/pub/linux/daemons/raid/alpha, or more recently from http://people.redhat.com/mingo/ The standard 2.2 kernels does not have direct support for the new-style RAID described in this HOWTO. Therefore these patches are needed. The old-style RAID support in standard 2.0 and 2.2 kernels is buggy and lacks several important features present in the new-style RAID software.
As of this writing, the new-style RAID support is being merged into the 2.3 development kernels, and will therefore (most likely) be present in the 2.4 Linux kernel when that one comes out. But until then, the stable kernels must be patched manually.
You might want to use the -ac kernel releases done by Alan
Cox, for RAID support in 2.2. Some of those contain the
new-style RAID, and that will save you from patching the kernel
yourself.
Some of the information in this HOWTO may seem trivial, if you know RAID all ready. Just skip those parts.
The mandatory disclaimer:
Although RAID seems stable for me, and stable for many other people, it may not work for you. If you lose all your data, your job, get hit by a truck, whatever, it's not my fault, nor the developers'. Be aware, that you use the RAID software and this information at your own risk! There is no guarantee whatsoever, that any of the software, or this information, is in anyway correct, nor suited for any use whatsoever. Back up all your data before experimenting with this. Better safe than sorry.
That said, I must also say that I haven't had a single stability problem with Software RAID, I use it on quite a few machines with no problems what so ever, and I haven't seen other people having problems with random crashes or instability caused by RAID.
This HOWTO assumes you are using a late 2.2.x or 2.0.x kernel with a matching raid0145 patch and the 0.90 version of the raidtools, or that you are using a late 2.3 kernel (version > 2.3.46) or eventually 2.4. Both the patches and the tools can be found at ftp://ftp.fi.kernel.org/pub/linux/daemons/raid/alpha, and in some cases at http://people.redhat.com/mingo/. The RAID patch, the raidtools package, and the kernel should all match as close as possible. At times it can be necessary to use older kernels if raid patches are not available for the latest kernel.
There can be many good reasons for using RAID. A few are; the ability to combine several physical disks into one larger ``virtual'' device, performance improvements, and redundancy.
Linux RAID can work on most block devices. It doesn't matter whether you use IDE or SCSI devices, or a mixture. Some people have also used the Network Block Device (NBD) with more or less success.
Be sure that the bus(ses) to the drives are fast enough. You shouldn't have 14 UW-SCSI drives on one UW bus, if each drive can give 10 MB/s and the bus can only sustain 40 MB/s. Also, you should only have one device per IDE bus. Running disks as master/slave is horrible for performance. IDE is really bad at accessing more that one drive per bus. Of Course, all newer motherboards have two IDE busses, so you can set up two disks in RAID without buying more controllers.
The RAID layer has absolutely nothing to do with the filesystem layer. You can put any filesystem on a RAID device, just like any other block device.
The word ``RAID'' means ``Linux Software RAID''. This HOWTO does not treat any aspects of Hardware RAID.
When describing setups, it is useful to refer to the number of disks and their sizes. At all times the letter N is used to denote the number of active disks in the array (not counting spare-disks). The letter S is the size of the smallest drive in the array, unless otherwise mentioned. The letter P is used as the performance of one disk in the array, in MB/s. When used, we assume that the disks are equally fast, which may not always be true.
Note that the words ``device'' and ``disk'' are supposed to mean about the same thing. Usually the devices that are used to build a RAID device are partitions on disks, not necessarily entire disks. But combining several partitions on one disk usually does not make sense, so the words devices and disks just mean ``partitions on different disks''.
Here's a short description of what is supported in the Linux RAID patches. Some of this information is absolutely basic RAID info, but I've added a few notices about what's special in the Linux implementation of the levels. Just skip this section if you know RAID. Then come back when you are having problems :)
The current RAID patches for Linux supports the following levels:
Spare disks are disks that do not take part in the RAID set until one of the active disks fail. When a device failure is detected, that device is marked as ``bad'' and reconstruction is immediately started on the first spare-disk available.
Thus, spare disks add a nice extra safety to especially RAID-5 systems that perhaps are hard to get to (physically). One can allow the system to run for some time, with a faulty device, since all redundancy is preserved by means of the spare disk.
You cannot be sure that your system will survive a disk crash. The RAID layer should handle device failures just fine, but SCSI drivers could be broken on error handling, or the IDE chipset could lock up, or a lot of other things could happen.
There's no reason to use RAID for swap performance reasons. The kernel itself can stripe swapping on several devices, if you just give them the same priority in the fstab file.
A nice fstab looks like:
/dev/sda2 swap swap defaults,pri=1 0 0 /dev/sdb2 swap swap defaults,pri=1 0 0 /dev/sdc2 swap swap defaults,pri=1 0 0 /dev/sdd2 swap swap defaults,pri=1 0 0 /dev/sde2 swap swap defaults,pri=1 0 0 /dev/sdf2 swap swap defaults,pri=1 0 0 /dev/sdg2 swap swap defaults,pri=1 0 0This setup lets the machine swap in parallel on seven SCSI devices. No need for RAID, since this has been a kernel feature for a long time.
Another reason to use RAID for swap is high availability. If you set up a system to boot on eg. a RAID-1 device, the system should be able to survive a disk crash. But if the system has been swapping on the now faulty device, you will for sure be going down. Swapping on the RAID-1 device would solve this problem.
There has been a lot of discussion about whether swap was stable on RAID devices. This is a continuing debate, because it depends highly on other aspects of the kernel as well. As of this writing, it seems that swapping on RAID should be perfectly stable, except for when the array is reconstructing (eg. after a new disk is inserted into a degraded array). When 2.4 comes out this is an issue that will most likely get addressed fairly quickly, but until then, you should stress-test the system yourself until you are either satisfied with the stability or conclude that you won't be swapping on RAID.
You can set up RAID in a swap file on a filesystem on your RAID device, or you can set up a RAID device as a swap partition, as you see fit. As usual, the RAID device is just a block device.
This section will mention some of the hardware concerns involved when running software RAID.
It is indeed possible to run RAID over IDE disks. And excellent performance can be achieved too. In fact, today's price on IDE drives and controllers does make IDE something to be considered, when setting up new RAID systems.
It is very important, that you only use one IDE disk per IDE bus. Not only would two disks ruin the performance, but the failure of a disk often guarantees the failure of the bus, and therefore the failure of all disks on that bus. In a fault-tolerant RAID setup (RAID levels 1,4,5), the failure of one disk can be handled, but the failure of two disks (the two disks on the bus that fails due to the failure of the one disk) will render the array unusable. Also, when the master drive on a bus fails, the slave or the IDE controller may get awfully confused. One bus, one drive, that's the rule.
There are cheap PCI IDE controllers out there. You often get two or four busses for around $80. Considering the much lower price of IDE disks versus SCSI disks, I'd say an IDE disk array could be a really nice solution if one can live with the relatively low (around 8 probably) disks one can attach to a typical system (unless of course, you have a lot of PCI slots for those IDE controllers).
IDE has major cabling problems though when it comes to large arrays. Even if you had enough PCI slots, it's unlikely that you could fit much more than 8 disks in a system and still get it running without data corruption (caused by too long IDE cables).
This has been a hot topic on the linux-kernel list for some time. Although hot swapping of drives is supported to some extent, it is still not something one can do easily.
Don't ! IDE doesn't handle hot swapping at all. Sure, it may work for you, if your IDE driver is compiled as a module (only possible in the 2.2 series of the kernel), and you re-load it after you've replaced the drive. But you may just as well end up with a fried IDE controller, and you'll be looking at a lot more down-time than just the time it would have taken to replace the drive on a downed system.
The main problem, except for the electrical issues that can destroy your hardware, is that the IDE bus must be re-scanned after disks are swapped. The current IDE driver can't do that. If the new disk is 100% identical to the old one (wrt. geometry etc.), it may work even without re-scanning the bus, but really, you're walking the bleeding edge here.
Normal SCSI hardware is not hot-swappable either. It may however work. If your SCSI driver supports re-scanning the bus, and removing and appending devices, you may be able to hot-swap devices. However, on a normal SCSI bus you probably shouldn't unplug devices while your system is still powered up. But then again, it may just work (and you may end up with fried hardware).
The SCSI layer should survive if a disk dies, but not all SCSI drivers handle this yet. If your SCSI driver dies when a disk goes down, your system will go with it, and hot-plug isn't really interesting then.
With SCA, it should be possible to hot-plug devices. However, I don't have the hardware to try this out, and I haven't heard from anyone who's tried, so I can't really give any recipe on how to do this.
If you want to play with this, you should know about SCSI and RAID internals anyway. So I'm not going to write something here that I can't verify works, instead I can give a few clues:
Not all SCSI drivers support appending and removing devices. In the 2.2 series of the kernel, at least the Adaptec 2940 and Symbios NCR53c8xx drivers seem to support this, others may and may not. I'd appreciate if anyone has additional facts here...
This is what you need for any of the RAID levels:
All this software can be found at ftp://ftp.fi.kernel.org/pub/linux The RAID
tools and patches are in the daemons/raid/alpha
subdirectory. The kernels are found in the kernel
subdirectory.
Patch the kernel, configure it to include RAID support for the level you want to use. Compile it and install it.
Then unpack, configure, compile and install the RAID tools.
Ok, so far so good. If you reboot now, you should have a file called
/proc/mdstat. Remember it, that file is your friend. See
what it contains, by doing a cat /proc/mdstat. It should
tell you that you have the right RAID personality (eg. RAID mode)
registered, and that no RAID devices are currently active.
Create the partitions you want to include in your RAID set.
Now, let's go mode-specific.
Ok, so you have two or more partitions which are not necessarily the same size (but of course can be), which you want to append to each other.
Set up the /etc/raidtab file to describe your
setup. I set up a raidtab for two disks in linear mode, and the file
looked like this:
raiddev /dev/md0
raid-level linear
nr-raid-disks 2
chunk-size 32
persistent-superblock 1
device /dev/sdb6
raid-disk 0
device /dev/sdc5
raid-disk 1
Spare-disks are not supported here. If a disk dies, the array dies
with it. There's no information to put on a spare disk.
You're probably wondering why we specify a chunk-size here
when linear mode just appends the disks into one large array with no
parallelism. Well, you're completely right, it's odd. Just put in some
chunk size and don't worry about this any more.
Ok, let's create the array. Run the command
mkraid /dev/md0
This will initialize your array, write the persistent superblocks, and start the array.
Have a look in /proc/mdstat. You should see that the array is running.
Now, you can create a filesystem, just like you would on any other device, mount it, include it in your fstab and so on.
You have two or more devices, of approximately the same size, and you want to combine their storage capacity and also combine their performance by accessing them in parallel.
Set up the /etc/raidtab file to describe your configuration. An
example raidtab looks like:
raiddev /dev/md0
raid-level 0
nr-raid-disks 2
persistent-superblock 1
chunk-size 4
device /dev/sdb6
raid-disk 0
device /dev/sdc5
raid-disk 1
Like in Linear mode, spare disks are not supported here either. RAID-0
has no redundancy, so when a disk dies, the array goes with it.
Again, you just run
mkraid /dev/md0to initialize the array. This should initialize the superblocks and start the raid device. Have a look in
/proc/mdstat to see what's
going on. You should see that your device is now running.
/dev/md0 is now ready to be formatted, mounted, used and abused.
You have two devices of approximately same size, and you want the two to be mirrors of each other. Eventually you have more devices, which you want to keep as stand-by spare-disks, that will automatically become a part of the mirror if one of the active devices break.
Set up the /etc/raidtab file like this:
raiddev /dev/md0
raid-level 1
nr-raid-disks 2
nr-spare-disks 0
chunk-size 4
persistent-superblock 1
device /dev/sdb6
raid-disk 0
device /dev/sdc5
raid-disk 1
If you have spare disks, you can add them to the end of the device
specification like
device /dev/sdd5
spare-disk 0
Remember to set the nr-spare-disks entry correspondingly.
Ok, now we're all set to start initializing the RAID. The mirror must be constructed, eg. the contents (however unimportant now, since the device is still not formatted) of the two devices must be synchronized.
Issue the
mkraid /dev/md0command to begin the mirror initialization.
Check out the /proc/mdstat file. It should tell you that the /dev/md0
device has been started, that the mirror is being reconstructed, and
an ETA of the completion of the reconstruction.
Reconstruction is done using idle I/O bandwidth. So, your system should still be fairly responsive, although your disk LEDs should be glowing nicely.
The reconstruction process is transparent, so you can actually use the device even though the mirror is currently under reconstruction.
Try formatting the device, while the reconstruction is running. It will work. Also you can mount it and use it while reconstruction is running. Of Course, if the wrong disk breaks while the reconstruction is running, you're out of luck.
Note! I haven't tested this setup myself. The setup below is my best guess, not something I have actually had up running.
You have three or more devices of roughly the same size, one device is significantly faster than the other devices, and you want to combine them all into one larger device, still maintaining some redundancy information. Eventually you have a number of devices you wish to use as spare-disks.
Set up the /etc/raidtab file like this:
raiddev /dev/md0
raid-level 4
nr-raid-disks 4
nr-spare-disks 0
persistent-superblock 1
chunk-size 32
device /dev/sdb1
raid-disk 0
device /dev/sdc1
raid-disk 1
device /dev/sdd1
raid-disk 2
device /dev/sde1
raid-disk 3
If we had any spare disks, they would be inserted in a similar way,
following the raid-disk specifications;
device /dev/sdf1
spare-disk 0
as usual.
Your array can be initialized with the
mkraid /dev/md0command as usual.
You should see the section on special options for mke2fs before formatting the device.
You have three or more devices of roughly the same size, you want to combine them into a larger device, but still to maintain a degree of redundancy for data safety. Eventually you have a number of devices to use as spare-disks, that will not take part in the array before another device fails.
If you use N devices where the smallest has size S, the size of the entire array will be (N-1)*S. This ``missing'' space is used for parity (redundancy) information. Thus, if any disk fails, all data stay intact. But if two disks fail, all data is lost.
Set up the /etc/raidtab file like this:
raiddev /dev/md0
raid-level 5
nr-raid-disks 7
nr-spare-disks 0
persistent-superblock 1
parity-algorithm left-symmetric
chunk-size 32
device /dev/sda3
raid-disk 0
device /dev/sdb1
raid-disk 1
device /dev/sdc1
raid-disk 2
device /dev/sdd1
raid-disk 3
device /dev/sde1
raid-disk 4
device /dev/sdf1
raid-disk 5
device /dev/sdg1
raid-disk 6
If we had any spare disks, they would be inserted in a similar way,
following the raid-disk specifications;
device /dev/sdh1
spare-disk 0
And so on.
A chunk size of 32 KB is a good default for many general purpose filesystems of this size. The array on which the above raidtab is used, is a 7 times 6 GB = 36 GB (remember the (n-1)*s = (7-1)*6 = 36) device. It holds an ext2 filesystem with a 4 KB block size. You could go higher with both array chunk-size and filesystem block-size if your filesystem is either much larger, or just holds very large files.
Ok, enough talking. You set up the raidtab, so let's see if it works. Run the
mkraid /dev/md0command, and see what happens. Hopefully your disks start working like mad, as they begin the reconstruction of your array. Have a look in
/proc/mdstat to see what's going on.
If the device was successfully created, the reconstruction process has now begun. Your array is not consistent until this reconstruction phase has completed. However, the array is fully functional (except for the handling of device failures of course), and you can format it and use it even while it is reconstructing.
See the section on special options for mke2fs before formatting the array.
Ok, now when you have your RAID device running, you can always stop it or re-start it using the
raidstop /dev/md0or
raidstart /dev/md0commands.
Instead of putting these into init-files and rebooting a zillion times to make that work, read on, and get autodetection running.
Back in ``The Good Old Days'' (TM), the raidtools would read your
/etc/raidtab file, and then initialize the array. However, this would
require that the filesystem on which /etc/raidtab resided was
mounted. This is unfortunate if you want to boot on a RAID.
Also, the old approach led to complications when mounting filesystems
on RAID devices. They could not be put in the /etc/fstab file as usual,
but would have to be mounted from the init-scripts.
The persistent superblocks solve these problems. When an array is
initialized with the persistent-superblock option in the
/etc/raidtab file, a special superblock is written in the beginning of
all disks participating in the array. This allows the kernel to read
the configuration of RAID devices directly from the disks involved,
instead of reading from some configuration file that may not be
available at all times.
You should however still maintain a consistent /etc/raidtab file, since
you may need this file for later reconstruction of the array.
The persistent superblock is mandatory if you want auto-detection of your RAID devices upon system boot. This is described in the Autodetection section.
The chunk-size deserves an explanation. You can never write completely parallel to a set of disks. If you had two disks and wanted to write a byte, you would have to write four bits on each disk, actually, every second bit would go to disk 0 and the others to disk 1. Hardware just doesn't support that. Instead, we choose some chunk-size, which we define as the smallest ``atomic'' mass of data that can be written to the devices. A write of 16 KB with a chunk size of 4 KB, will cause the first and the third 4 KB chunks to be written to the first disk, and the second and fourth chunks to be written to the second disk, in the RAID-0 case with two disks. Thus, for large writes, you may see lower overhead by having fairly large chunks, whereas arrays that are primarily holding small files may benefit more from a smaller chunk size.
Chunk sizes must be specified for all RAID levels, including linear mode. However, the chunk-size does not make any difference for linear mode.
For optimal performance, you should experiment with the value, as well as with the block-size of the filesystem you put on the array.
The argument to the chunk-size option in /etc/raidtab specifies the
chunk-size in kilobytes. So ``4'' means ``4 KB''.
Data is written ``almost'' in parallel to the disks in the
array. Actually, chunk-size bytes are written to each disk,
serially.
If you specify a 4 KB chunk size, and write 16 KB to an array of three disks, the RAID system will write 4 KB to disks 0, 1 and 2, in parallel, then the remaining 4 KB to disk 0.
A 32 KB chunk-size is a reasonable starting point for most arrays. But the optimal value depends very much on the number of drives involved, the content of the file system you put on it, and many other factors. Experiment with it, to get the best performance.
For writes, the chunk-size doesn't affect the array, since all data must be written to all disks no matter what. For reads however, the chunk-size specifies how much data to read serially from the participating disks. Since all active disks in the array contain the same information, reads can be done in a parallel RAID-0 like manner.
When a write is done on a RAID-4 array, the parity information must be
updated on the parity disk as well. The chunk-size is the size of the
parity blocks. If one byte is written to a RAID-4 array, then
chunk-size bytes will be read from the N-1 disks, the parity
information will be calculated, and chunk-size bytes written
to the parity disk.
The chunk-size affects read performance in the same way as in RAID-0, since reads from RAID-4 are done in the same way.
On RAID-5 the chunk-size has exactly the same meaning as in RAID-4.
A reasonable chunk-size for RAID-5 is 128 KB, but as always, you may want to experiment with this.
Also see the section on special options for mke2fs. This affects RAID-5 performance.
There is a special option available when formatting RAID-4 or -5
devices with mke2fs. The -R stride=nn option will allow
mke2fs to better place different ext2 specific data-structures in an
intelligent way on the RAID device.
If the chunk-size is 32 KB, it means, that 32 KB of consecutive data will reside on one disk. If we want to build an ext2 filesystem with 4 KB block-size, we realize that there will be eight filesystem blocks in one array chunk. We can pass this information on the mke2fs utility, when creating the filesystem:
mke2fs -b 4096 -R stride=8 /dev/md0
RAID-{4,5} performance is severely influenced by this option. I am unsure how the stride option will affect other RAID levels. If anyone has information on this, please send it in my direction.
The ext2fs blocksize severely influences the performance of the filesystem. You should always use 4KB block size on any filesystem larger than a few hundred megabytes, unless you store a very large number of very small files on it.
Autodetection allows the RAID devices to be automatically recognized by the kernel at boot-time, right after the ordinary partition detection is done.
This requires several things:
NOTE: Be sure that your RAID is NOT RUNNING before changing the
partition types. Use raidstop /dev/md0 to stop the device.
If you set up 1, 2 and 3 from above, autodetection should be set
up. Try rebooting. When the system comes up, cat'ing /proc/mdstat
should tell you that your RAID is running.
During boot, you could see messages similar to these:
Oct 22 00:51:59 malthe kernel: SCSI device sdg: hdwr sector= 512 bytes. Sectors= 12657717 [6180 MB] [6.2 GB] Oct 22 00:51:59 malthe kernel: Partition check: Oct 22 00:51:59 malthe kernel: sda: sda1 sda2 sda3 sda4 Oct 22 00:51:59 malthe kernel: sdb: sdb1 sdb2 Oct 22 00:51:59 malthe kernel: sdc: sdc1 sdc2 Oct 22 00:51:59 malthe kernel: sdd: sdd1 sdd2 Oct 22 00:51:59 malthe kernel: sde: sde1 sde2 Oct 22 00:51:59 malthe kernel: sdf: sdf1 sdf2 Oct 22 00:51:59 malthe kernel: sdg: sdg1 sdg2 Oct 22 00:51:59 malthe kernel: autodetecting RAID arrays Oct 22 00:51:59 malthe kernel: (read) sdb1's sb offset: 6199872 Oct 22 00:51:59 malthe kernel: bind<sdb1,1> Oct 22 00:51:59 malthe kernel: (read) sdc1's sb offset: 6199872 Oct 22 00:51:59 malthe kernel: bind<sdc1,2> Oct 22 00:51:59 malthe kernel: (read) sdd1's sb offset: 6199872 Oct 22 00:51:59 malthe kernel: bind<sdd1,3> Oct 22 00:51:59 malthe kernel: (read) sde1's sb offset: 6199872 Oct 22 00:51:59 malthe kernel: bind<sde1,4> Oct 22 00:51:59 malthe kernel: (read) sdf1's sb offset: 6205376 Oct 22 00:51:59 malthe kernel: bind<sdf1,5> Oct 22 00:51:59 malthe kernel: (read) sdg1's sb offset: 6205376 Oct 22 00:51:59 malthe kernel: bind<sdg1,6> Oct 22 00:51:59 malthe kernel: autorunning md0 Oct 22 00:51:59 malthe kernel: running: <sdg1><sdf1><sde1><sdd1><sdc1><sdb1> Oct 22 00:51:59 malthe kernel: now! Oct 22 00:51:59 malthe kernel: md: md0: raid array is not clean -- starting background reconstructionThis is output from the autodetection of a RAID-5 array that was not cleanly shut down (eg. the machine crashed). Reconstruction is automatically initiated. Mounting this device is perfectly safe, since reconstruction is transparent and all data are consistent (it's only the parity information that is inconsistent - but that isn't needed until a device fails).
Autostarted devices are also automatically stopped at shutdown. Don't worry about init scripts. Just use the /dev/md devices as any other /dev/sd or /dev/hd devices.
Yes, it really is that easy.
You may want to look in your init-scripts for any raidstart/raidstop commands. These are often found in the standard RedHat init scripts. They are used for old-style RAID, and has no use in new-style RAID with autodetection. Just remove the lines, and everything will be just fine.
There are several ways to set up a system that mounts it's root filesystem on a RAID device. At the moment, only the graphical install of RedHat Linux 6.1 allows direct installation to a RAID device. So most likely you're in for a little tweaking if you want this, but it is indeed possible.
The latest official lilo distribution (Version 21) doesn't handle RAID
devices, and thus the kernel cannot be loaded at boot-time from a RAID
device. If you use this version, your /boot filesystem will
have to reside on a non-RAID device. A way to ensure that your system
boots no matter what is, to create similar /boot partitions
on all drives in your RAID, that way the BIOS can always load data
from eg. the first drive available. This requires that you do not
boot with a failed disk in your system.
With redhat 6.1 a patch to lilo 21 has become available that can
handle /boot on RAID-1. Note that it doesn't work for any
other level, RAID-1 (mirroring) is the only supported RAID level. This
patch (lilo.raid1) can be found in dist/redhat-6.1/SRPMS/SRPMS/lilo-0.21-10.src.rpm on any redhat
mirror. The patched version of LILO will accept boot=/dev/md0
in lilo.conf and will make each disk in the mirror bootable.
Another way of ensuring that your system can always boot is, to create
a boot floppy when all the setup is done. If the disk on which the
/boot filesystem resides dies, you can always boot from the
floppy.
In order to have a system booting on RAID, the root filesystem (/) must be mounted on a RAID device. Two methods for achieving this is supplied bellow. Because none of the current distributions (that I know of at least) support installing on a RAID device, the methods assume that you install on a normal partition, and then - when the installation is complete - move the contents of your non-RAID root filesystem onto a new RAID device.
This method assumes you have a spare disk you can install the system on, which is not part of the RAID you will be configuring.
mke2fs), and mount it under /mnt/newrootcd / find . -xdev | cpio -pm /mnt/newroot
/mnt/newroot/etc/fstab file to
use the correct device (the /dev/md? root device) for the
root filesystem./boot filesystem, and mount
the boot device on /mnt/newroot/boot instead. This is
required for LILO to run successfully in the next step./mnt/newroot/etc/lilo.conf to point to the right
devices. The boot device must still be a regular disk (non-RAID
device), but the root device should point to your new RAID. When
done, run
lilo -r /mnt/newrootThis LILO run should complete with no errors.
If you're doing this with IDE disks, be sure to tell your BIOS that all disks are ``auto-detect'' types, so that the BIOS will allow your machine to boot even when a disk is missing.
This method requires that you use a raidtools/patch that includes the failed-disk directive. This will be the tools/patch for all kernels from 2.2.10 and later.
You can only use this method on RAID levels 1 and above. The idea is to install a system on a disk which is purposely marked as failed in the RAID, then copy the system to the RAID which will be running in degraded mode, and finally making the RAID use the no-longer needed ``install-disk'', zapping the old installation but making the RAID run in non-degraded mode.
failed-disk in the raidtab file. Don't put the
failed-disk as the first disk in the raidtab, that will give
you problems with starting the RAID. Create the RAID, and put a
filesystem on it.raidtab file to include the previously
failed-disk as a normal raid-disk. Now,
raidhotadd the disk to your RAID.
For the kernel to be able to mount the root filesystem, all support for the device on which the root filesystem resides, must be present in the kernel. Therefore, in order to mount the root filesystem on a RAID device, the kernel must have RAID support.
The normal way of ensuring that the kernel can see the RAID device is to simply compile a kernel with all necessary RAID support compiled in. Make sure that you compile the RAID support into the kernel, and not as loadable modules. The kernel cannot load a module (from the root filesystem) before the root filesystem is mounted.
However, since RedHat-6.0 ships with a kernel that has new-style RAID support as modules, I here describe how one can use the standard RedHat-6.0 kernel and still have the system boot on RAID.
You will have to instruct LILO to use a RAM-disk in order to achieve
this. Use the mkinitrd command to create a ramdisk containing
all kernel modules needed to mount the root partition. This can be
done as:
mkinitrd --with=<module> <ramdisk name> <kernel>For example:
mkinitrd --with=raid5 raid-ramdisk 2.2.5-22
This will ensure that the specified RAID module is present at boot-time, for the kernel to use when mounting the root device.
Never NEVER never re-partition disks that are part of a running RAID. If you must alter the partition table on a disk which is a part of a RAID, stop the array first, then repartition.
It is easy to put too many disks on a bus. A normal Fast-Wide SCSI bus can sustain 10 MB/s which is less than many disks can do alone today. Putting six such disks on the bus will of course not give you the expected performance boost.
More SCSI controllers will only give you extra performance, if the SCSI busses are nearly maxed out by the disks on them. You will not see a performance improvement from using two 2940s with two old SCSI disks, instead of just running the two disks on one controller.
If you forget the persistent-superblock option, your array may not start up willingly after it has been stopped. Just re-create the array with the option set correctly in the raidtab.
If a RAID-5 fails to reconstruct after a disk was removed and re-inserted, this may be because of the ordering of the devices in the raidtab. Try moving the first ``device ...'' and ``raid-disk ...'' pair to the bottom of the array description in the raidtab file.
Most of the ``error reports'' we see on linux-kernel, are from people who somehow failed to use the right RAID-patch with the right version of the raidtools. Make sure that if you're running 0.90 RAID, you're using the raidtools for it
If you plan to use RAID to get fault-tolerance, you may also want to test your setup, to see if it really works. Now, how does one simulate a disk failure ?
The short story is, that you can't, except perhaps for putting a fire axe thru the drive you want to ``simulate'' the fault on. You can never know what will happen if a drive dies. It may electrically take the bus it's attached to with it, rendering all drives on that bus inaccessible. I've never heard of that happening though. The drive may also just report a read/write fault to the SCSI/IDE layer, which in turn makes the RAID layer handle this situation gracefully. This is fortunately the way things often go.
If you want to simulate a drive failure, then plug out the drive. You should do this with the power off. If you are interested in testing whether your data can survive with a disk less than the usual number, there is no point in being a hot-plug cowboy here. Take the system down, unplug the disk, and boot it up again.
Look in the syslog, and look at /proc/mdstat to see how the RAID is
doing. Did it work ?
Remember, that you must be running RAID-{1,4,5} for your array to be able to survive a disk failure. Linear- or RAID-0 will fail completely when a device is missing.
When you've re-connected the disk again (with the power off, of
course, remember), you can add the ``new'' device to the RAID again,
with the raidhotadd command.
RAID (be it hardware- or software-), assumes that if a write to a disk doesn't return an error, then the write was successful. Therefore, if your disk corrupts data without returning an error, your data will become corrupted. This is of course very unlikely to happen, but it is possible, and it would result in a corrupt filesystem.
RAID cannot and is not supposed to guard against data corruption on
the media. Therefore, it doesn't make any sense either, to purposely
corrupt data (using dd for example) on a disk to see how the
RAID system will handle that. It is most likely (unless you corrupt
the RAID superblock) that the RAID layer will never find out about the
corruption, but your filesystem on the RAID device will be corrupted.
This is the way things are supposed to work. RAID is not a guarantee for data integrity, it just allows you to keep your data if a disk dies (that is, with RAID levels above or equal one, of course).
If you've read the rest of this HOWTO, you should already have a pretty good idea about what reconstruction of a degraded RAID involves. I'll summarize:
raidhotadd /dev/mdX /dev/sdX to re-insert the disk
in the arrayWell, it usually is, unless you're unlucky and you RAID has been rendered unusable because more disks than the ones redundant failed. This can actually happen if a number of disks reside on the same bus, and one disk takes the bus with it as it crashes. The other disks, however fine, will be unreachable to the RAID layer, because the bus is down, and they will be marked as faulty. On a RAID-5 where you can spare one disk, loosing two or more disks can be fatal.
The following section is the explanation that Martin Bene gave to me,
and describes a possible recovery from the scary scenario outlined
above. It involves using the failed-disk directive in your
/etc/raidtab, so this will only work on kernels 2.2.10 and later.
The scenario is:
One thing left: rewrite the RAID superblocks by mkraid --force
To get this to work, you'll need to have an up to date /etc/raidtab - if
it doesn't EXACTLY match devices and ordering of the original
disks this won't work.
Look at the sylog produced by trying to start the array, you'll see the event count for each superblock; usually it's best to leave out the disk with the lowest event count, i.e the oldest one.
If you mkraid without failed-disk, the recovery
thread will kick in immediately and start rebuilding the parity blocks
- not necessarily what you want at that moment.
With failed-disk you can specify exactly which disks you want
to be active and perhaps try different combinations for best
results. BTW, only mount the filesystem read-only while trying this
out... This has been successfully used by at least two guys I've been in
contact with.
This section contains a number of benchmarks from a real-world system using software RAID.
Benchmarks are done with the bonnie program, and at all times
on files twice- or more the size of the physical RAM in the machine.
The benchmarks here only measures input and output bandwidth
on one large single file. This is a nice thing to know, if it's
maximum I/O throughput for large reads/writes one is interested in.
However, such numbers tell us little about what the performance would
be if the array was used for a news spool, a web-server, etc. etc.
Always keep in mind, that benchmarks numbers are the result of running
a ``synthetic'' program. Few real-world programs do what
bonnie does, and although these I/O numbers are nice to look
at, they are not ultimate real-world-appliance performance
indicators. Not even close.
For now, I only have results from my own machine. The setup is:
The three U2W disks hang off the U2W controller, and the UW disk off the UW controller.
It seems to be impossible to push much more than 30 MB/s thru the SCSI busses on this system, using RAID or not. My guess is, that because the system is fairly old, the memory bandwidth sucks, and thus limits what can be sent thru the SCSI controllers.
Read is Sequential block input, and Write is Sequential block output. File size was 1GB in all tests. The tests where done in single-user mode. The SCSI driver was configured not to use tagged command queuing.
|
Chunk size | Block size | Read KB/s | Write KB/s |
| 4k | 1k | 19712 | 18035 |
| 4k | 4k | 34048 | 27061 |
| 8k | 1k | 19301 | 18091 |
| 8k | 4k | 33920 | 27118 |
| 16k | 1k | 19330 | 18179 |
| 16k | 2k | 28161 | 23682 |
| 16k | 4k | 33990 | 27229 |
| 32k | 1k | 19251 | 18194 |
| 32k | 4k | 34071 | 26976 |
From this it seems that the RAID chunk-size doesn't make that much of a difference. However, the ext2fs block-size should be as large as possible, which is 4KB (eg. the page size) on IA-32.
This time, the SCSI driver was configured to use tagged command queuing, with a queue depth of 8. Otherwise, everything's the same as before.
|
Chunk size | Block size | Read KB/s | Write KB/s |
| 32k | 4k | 33617 | 27215 |
No more tests where done. TCQ seemed to slightly increase write performance, but there really wasn't much of a difference at all.
The array was configured to run in RAID-5 mode, and similar tests where done.
|
Chunk size | Block size | Read KB/s | Write KB/s |
| 8k | 1k | 11090 | 6874 |
| 8k | 4k | 13474 | 12229 |
| 32k | 1k | 11442 | 8291 |
| 32k | 2k | 16089 | 10926 |
| 32k | 4k | 18724 | 12627 |
Now, both the chunk-size and the block-size seems to actually make a difference.
RAID-10 is ``mirrored stripes'', or, a RAID-1 array of two RAID-0 arrays. The chunk-size is the chunk sizes of both the RAID-1 array and the two RAID-0 arrays. I did not do test where those chunk-sizes differ, although that should be a perfectly valid setup.
|
Chunk size | Block size | Read KB/s | Write KB/s |
| 32k | 1k | 13753 | 11580 |
| 32k | 4k | 23432 | 22249 |
No more tests where done. The file size was 900MB, because the four partitions involved where 500 MB each, which doesn't give room for a 1G file in this setup (RAID-1 on two 1000MB arrays).
The following people contributed to the creation of this documentation:
Please submit corrections, suggestions etc. to the author. It's the only way this HOWTO can improve.