The 'no controlling tty problem' -> -o 'BatchMode yes' by Zot O'Connor <zot@crl.com>
warning about kernel 2.0.30 by mag
This is the Linux VPN howto, a collection of information on how to set up a Virtual Protected Network in Linux (and other unices in general).
This document is part of the Linux HOWTO project. The copyright notice is the following: Unless otherwise stated, Linux HOWTO documents are copyrighted by their respective authors. Linux HOWTO documents may be reproduced and distributed in whole or in part, in any medium physical or electronic, as long as this copyright notice is retained on all copies. Commercial redistribution is allowed and encouraged; however, the author would like to be notified of any such distributions. All translations, derivative works, or aggregate works incorporating any Linux HOWTO documents must be covered under this copyright notice. That is, you may not produce a derivative work from a HOWTO and impose additional restrictions on its distribution. Exceptions to these rules may be granted under certain conditions; please contact the Linux HOWTO coordinator at the address given below. In short, we wish to promote dissemination of this information through as many channels as possible. However, we do wish to retain copyright on the HOWTO documents, and would like to be notified of any plans to redistribute the HOWTOs. If you have questions, please contact Tim Bynum, the Linux HOWTO coordinator, at linux-howto@sunsite.unc.edu via email.
As usual: the author not responsible for any damage. For the correct wording, see the relevant part of the GNU GPL 0.1.1
We are dealing with security: you are not safe if you haven't got good security policy, and other rather boring things.
Thanks to all of who has written the tools used.
Thanks to Zot O'Connor <zot@crl.com> for pointing out the "no controlling tty" problem, and it's solution.
This is very preliminary. You should have thorough knowledge of administrating IP, at least some knowledge of firewalls, ppp and ssh. You should know them anyway if you want to set up a VPN. I just decided to write down my experiences not to forget them. There are possibly some security holes indeed. To be fair I've tried it on hosts configured as routers not firewalls, saying: It's simple from that point.
As firewalls are in more and more widely use in internet and intranet security, the ability to do nice VPNs is important. Here are my experiences. Comments are welcome.
I will use the terms "master firewall" and "slave firewall", though making a VPN has nothing to do with client-server architecture. I simply refer to them as the active and passive participants of the connection's setup. The host which is starts the setup will be referred as the master, and the passive participant will be the slave.
Before you start to set up your system, you should know the networking details. I assume you have two firewalls protecting one intranet per firewall, and they are both connected to the internet. So now you should have two network interfaces (at least) per firewall. Take a sheet of paper, write down their IP addresses and network mask. You will need one more IP adresses per firewall for the VPN you want to do now. Those addresses should be outside of your existing subnets. I suggest using addresses from the "private" address ranges. They are the followings:
For the sake of example, here's a sample configuration: The two bastions are called fellini and polanski. They have one interface for the internet (-out), one for the intranet (-in), and one for the vpn (-vpn). The addresses and netmasks:
So we have the plan.
You will need a
Current versions:
Compile or otherwise install the gathered tools. Look at every one's documentation (and the firewall-howto) for details. Now we have the tools.
Configure your firewall rules, etc. You need to enable ssh traffic between the two firewll hosts. It means a connection to port 22 on the slave from the master. Start sshd on the slave and verify if you can login. This step is untested, please tell me your results.
Create an account on the slave firewall use your favourite tool (e.g. vi, mkdir, chown, chmod) you might create an account on the master also, but I think you want to set up the connection at boot time, so your ordinary root account will do. Can anyone point out risks on using the root account on the master?
Use the ssh-keygen program. Set empty password for the private key if you want to do automatic setup of the VPN.
Copy the newly generated public key in the slave account under .ssh/authorized_keys, and set up file permissions like the following:
drwx------ 2 slave slave 1024 Apr 7 23:49 ./ drwx------ 4 slave slave 1024 Apr 24 14:05 ../ -rwx------ 1 slave slave 328 Apr 7 03:04 authorized_keys -rw------- 1 slave slave 660 Apr 14 15:23 known_hosts -rw------- 1 slave slave 512 Apr 21 10:03 random_seed
The first row being ~slave/.ssh, and the second is ~slave.
It means the followings on my setup in sshd_conf:
PermitRootLogin no IgnoreRhosts yes StrictModes yes QuietMode no FascistLogging yes KeepAlive yes RhostsAuthentication no RhostsRSAAuthentication no RSAAuthentication yes PasswordAuthentication no PermitEmptyPasswords no
Password authentication is turned off, so login is only possible with authorized keys. (You've turned off telnet and the 'r' commands of course).
As the master account is the root in my case, it has nothing to do. For the slave account, the following lines appear in /etc/sudoers:
Cmnd_Alias VPN=/usr/sbin/pppd,/usr/local/vpn/route slave ALL=NOPASSWD: VPN
As you can see, I am using some scripts to set up ppp and the routing tables on the slave host.
On the master host there is a full-blown init script I am using:
#! /bin/sh
# skeleton example file to build /etc/init.d/ scripts.
# This file should be used to construct scripts for /etc/init.d.
#
# Written by Miquel van Smoorenburg <miquels@cistron.nl>.
# Modified for Debian GNU/Linux
# by Ian Murdock <imurdock@gnu.ai.mit.edu>.
#
# Version: @(#)skeleton 1.6 11-Nov-1996 miquels@cistron.nl
#
PATH=/usr/local/sbin:/sbin:/bin:/usr/sbin:/usr/bin:/usr/bin/X11/:
PPPAPP=/home/slave/ppp
ROUTEAPP=/home/slave/route
PPPD=/usr/sbin/pppd
NAME=VPN
REDIR=/usr/local/bin/pty-redir
SSH=/usr/bin/ssh
MYPPPIP=192.168.0.1
TARGETIP=192.168.0.2
TARGETNET=193.6.37.0
MYNET=193.6.35.0
SLAVEWALL=polanski-out
SLAVEACC=slave
test -f $PPPD || exit 0
set -e
case "$1" in
start)
echo setting up vpn
$REDIR $SSH -o 'Batchmode yes' -t -l $SLAVEACC $SLAVEWALL sudo $PPPAPP >/tmp/device
TTYNAME=`cat /tmp/device`
echo tty is $TTYNAME
sleep 10s
if [ ! -z $TTYNAME ]
then
$PPPD $TTYNAME ${MYPPPIP}:${TARGETIP}
else
echo FAILED!
logger "vpn setup failed"
fi
sleep 5s
route add -net $TARGETNET gw $TARGETIP
$SSH -o 'Batchmode yes' -l $SLAVEACC $SLAVEWALL sudo $ROUTEAPP
;;
stop)
ps -ax | grep "ssh -t -l $SLAVEACC " | grep -v grep | awk '{print $1}' | xargs kill
;;
*)
# echo "Usage: /etc/init.d/$NAME {start|stop|reload}"
echo "Usage: /etc/init.d/$NAME {start|stop}"
exit 1
;;
esac
exit 0
The slave uses one script for routing setup (/usr/local/vpn/route):
#!/bin/bash /sbin/route add -net 193.6.35.0 gw 192.168.0.1
and its .ppprc consists of the following:
passive
The master logs in into the slave, starts pppd, and redirects this all thing into a local pty. It consists of the following steps:
There are (not very tight) timing considerations involved, this is why that 'sleep 10s'.
You've already tried if ssh works well, aren't you? If the slave refuses to log you in, read the logs. Perhaps there are problems with file permissions or the sshd setup.
Log in into slave, and issue:
sudo /usr/sbin/pppd passive
You should see garbage coming at this point. If it works good, if not, there is some problem either with sudo, either with pppd. Look what the commands had said, and at the logs and at the /etc/ppp/options, and the .ppprc file. If it works, write this 'passive' word into .ppprc, and try again. To get rid off the garbage and continue working, press enter,'~' and '^Z'. You should have the master's prompt now, and kill %1. See the section about tuning if you want to know more of the escape character.
Well, then
ssh -l slave polanski sudo /usr/sbin/pppd
should work also, and deliver the garbage right into your face.
Try to redirect this whole thing this time:
/usr/local/bin/pty-redir /usr/bin/ssh -l slave polanski sudo /usr/sbin/pppd
Nice long sentence isn't it? You should use the full path into the ssh executable, as the pty-redir program allows only this form for security reasons. Now you've got a device name from the program. Let's say, you've got /dev/ttyp0 You can use the ps command to look what has happened. Look for 'p0'
Try
/usr/sbin/pppd /dev/ttyp0 local 192.168.0.1:192.168.0.2
to establish the connection. Look at the output of the ifconfig command to see if the device has established, and use ping to check your virtual net.
Set up the routes on the master host, and on the slave also. Now you should be able to ping one host in one intranet from other host in the other intranet. Set up the additional firewalling rules. Now as you have the VPN, you can set up the rules concerning the connectivity of the two intranets.
As I said this HOWTO is mainly a quick memo on how I had set up a VPN. There are things in the configuration I didn't experiment yet. These things will go into their place when I try them, or anyone tells me "it works in the following way" The most important thing is that the connection ppp uses is not 8-bit yet. I believe it has something to do either with ssh configuration or the pty setup. In this configuration ssh uses the tilde (~) character as an escape character. It might stop or slow down the communication, as any newline-tilde sequence causes ssh to give a prompt. Ssh documentation said: <On most systems, setting the escape character to ``none'' will also make the session transparent even if a tty is used.> The corresponding flag to ssh is '-e', and you can also set it in the configuration file.
Creating anything virtual comes with utilization of real-world resources. A VPN eats up bandwidth and computing resources. The goal would be to get balance between the two. You can tune it with the '-C' switch or the 'CompressionLevel' option. You might try using another cipher, but I don't recommend it. Also note that the round-trip-time can be longer if you use better compression. Any experiments on it are welcome.
I try to cover here the vulnerability issues arising from this particular setup and VPNs in general. Any comments are warmly welcome.